 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| MASW-002103-1363 HMICTM Silicon PIN Diode SPDT Switch 50 MHz - 20 GHz Features Specified from 50 MHz to 20 GHz Usable up to 26 GHz Low Insertion Loss High Isolation Low Parasitic Capacitance and Inductance RoHS Compliant SurmountTM Package Rugged, Fully Monolithic Glass Encapsulated Construction Up to +38 dBm C.W. Power Handling1 @ +25C Silicon Nitride Passivation Polymer Scratch Protection Rev. V7 Description The MASW-002103-1363 is a SurmountTM broadband monolithic SPDT switch using series and shunt connected silicon PIN diodes. This part is designed for use as a moderate signal, high performance switch in applications up to 20 GHz. This Surface Mount chipscale configuration is optimized for broadband performance with minimal associated parasitics usually associated with hybrid MMIC designs incorporating beam lead and PIN diodes that require chip and wire assembly. The MASW-002103-1363 is fabricated using M/A-COM Tech's patented HMICTM (Heterolithic Microwave Integrated Circuit) process, US Patent 5,268,310. This process allows the incorporation of silicon pedestals that form series and shunt diodes or vias by imbedding them in low loss, low dispersion glass. By using small spacing between elements, this combination of silicon and glass gives HMIC devices low loss and high isolation performance through low millimeter frequencies. Selective backside metalization is applied producing a surface mount device. The topside is fully encapsulated with silicon nitride and has an additional polymer layer for scratch and impact protection. These protective coatings prevent damage to the junction and the anode airbridge during handling and assembly. 2. Functional Schematic J3 J1 J2 Pin Configuration 2 Pin J1 J2 J3 Function RFC RF1 RF2 The exposed pad centered on the chip bottom must be connected to RF and DC ground. Ordering Information Part Number MASW-002103-13630G MASW-002103-13635P Package 50 piece gel pack 500 piece reel 3000 piece reel Sample Test Board 1. Power Handling Testing performed @ 2GHz MASW-002103-13630P MASW-002103-001SMB 1 ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions * North America Tel: 800.366.2266 * Europe Tel: +353.21.244.6400 is considering for development. Performance is based on target specifications, simulated results, * India Tel: +91.80.43537383 * China Tel: +86.21.2407.1588 and/or prototype measurements. Commitment to develop is not guaranteed. Visit www.macomtech.com for additional data sheets and product information. PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology Solutions has under development. Performance is based on engineering tests. Specifications are typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available. M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make Commitment to produce in volume is not guaranteed. changes to the product(s) or information contained herein without notice. MASW-002103-1363 HMICTM Silicon PIN Diode SPDT Switch 50 MHz - 20 GHz Electrical Specifications: TA = 25C, PIN = 0 dBm, Z0 = 50 , 20mA/-10V Parameter Insertion Loss Frequency 6 GHz 13 GHz 20 GHz 6 GHz 13 GHz 20 GHz 6 GHz 13 GHz 20 GHz 2 GHz 0.05 GHz, 5 MHz Spacing, +10dBm 0.5 GHz, 5 MHz Spacing ,+20dBm 1 GHz, 10 MHz Spacing, +20dBm 2 GHz, 10 MHz Spacing, +20dBm 3 Rev. V7 Units dB Min. -- -- -- 45 33 23 20 17.3 16.5 -- -- -- -- -- -- -- Typ. 0.55 0.80 1.05 52 38 27 25 23 23 36 45 59 63 66 20 -- Max. 0.63 0.93 1.25 -- -- -- -- -- -- -- -- -- -- -- -- 80 Input to Output Isolation dB Return Loss dB Input 0.1dB Compression Point dBm IIP3 dBm ns V Switching Speed Voltage Rating 3. 4. 4 -- -- Typical Switching Speed measured fro 10% to 90 % of detected RF signal driven by TTL compatible drivers. Maximum reverse leakage current in either the shunt or series PIN diodes shall be 0.5 uA maximum @ -80 volts. Absolute Maximum Ratings 5,6 Parameter Operating Temperature Storage Temperature Junction Temperature Applied Reverse Voltage RF CW Incident Power Bias Current +25C Absolute Maximum -65 C to +125 C -65 C to +150 C +175 C |-80 V| 38dBm CW @ 2GHz,+25C 33dBm CW @ 20GHz,+25C 50 mA Handling Procedures Please observe the following precautions to avoid damage: Static Sensitivity These devices are rated at Class 1A Human Body Model. Proper ESD control techniques should be used when handling these devices. Max Operating Conditions for combination RF Pwr, DC Bias, & Temp: 33dBm CW @ 20mA per Diode @ +85C @ 2GHz 5. 6. Exceeding any one or combination of these limits may cause permanent damage to this device. M/A-COM Tech does not recommend sustained operation near these survivability limits. 2 ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions * North America Tel: 800.366.2266 * Europe Tel: +353.21.244.6400 is considering for development. Performance is based on target specifications, simulated results, * India Tel: +91.80.43537383 * China Tel: +86.21.2407.1588 and/or prototype measurements. Commitment to develop is not guaranteed. Visit www.macomtech.com for additional data sheets and product information. PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology Solutions has under development. Performance is based on engineering tests. Specifications are typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available. M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make Commitment to produce in volume is not guaranteed. changes to the product(s) or information contained herein without notice. MASW-002103-1363 HMICTM Silicon PIN Diode SPDT Switch 50 MHz - 20 GHz Typical Small Signal Performance at +25C (On-Wafer RF Test) MASW-002103-1363 Insertion Loss Forw ard Bias (On-arm ): -10V, -20m A, Reverse Bias (Off-arm ): 20m A 0.00 -1 0.00 Rev. V7 0.00 -0.20 MASW-002103-1363 Isolation Forw ard Bias (On-arm ):-10V, -20m A, Reverse Bias (Off-arm ): 20m A Insertion Loss (dB) -0.40 -0.80 -1 .00 -1 .20 -1 .40 -1 .60 -1 .80 -2.00 0.0 5.0 1 0.0 1 5.0 20.0 25.0 30.0 Isolation (dB) -0.60 -20.00 -30.00 -40.00 -50.00 -60.00 -70.00 -80.00 0.0 5.0 1 0.0 1 5.0 20.0 25.0 30.0 Frequency (GHz) Frequency (GHz) MASW-002103-1363 Maximum Input Power Curve Baseplate Temperature fixed @ 25degC 0.00 -5.00 -1 0.00 -1 5.00 -20.00 -25.00 -30.00 -35.00 -40.00 -45.00 0.0 MASW-002103-1363 Return Loss Forw ard Bias (On-arm ): -10V, -20m A, Reverse Bias (Off-arm ): 20m A Input Power (Watts) 12 10 Return Loss (dB) Input J1 to J2 Input J1 to J3 8 6 4 2 2GHz, 6.7W Output J2 Output J3 5.0 1 0.0 1 5.0 20.0 25.0 30.0 10GHz, 3.5W 20GHz, 2W 0 0 0.2 0.4 0.6 0.8 1 1.2 1.4 1.6 Insertion Loss (dB) Freq [GHz] 3 ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions * North America Tel: 800.366.2266 * Europe Tel: +353.21.244.6400 is considering for development. Performance is based on target specifications, simulated results, * India Tel: +91.80.43537383 * China Tel: +86.21.2407.1588 and/or prototype measurements. Commitment to develop is not guaranteed. Visit www.macomtech.com for additional data sheets and product information. PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology Solutions has under development. Performance is based on engineering tests. Specifications are typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available. M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make Commitment to produce in volume is not guaranteed. changes to the product(s) or information contained herein without notice. MASW-002103-1363 HMICTM Silicon PIN Diode SPDT Switch 50 MHz - 20 GHz Bias Control Optimal operation of the MASW-002103-1363 is achieved by simultaneous application of negative DC voltage and current to the low loss switching arm and positive DC voltage and current to the remaining switching arm as shown in the applications circuit below. DC return is achieved via R2 on the RFC path. In the low loss state, the series diode must be forward biased with current and the shunt diode reverse biased with voltage. In the isolated arm, the shunt diode is forward biased with current and the series diode is reverse biased with voltage. Rev. V7 Driver Connections Control Level (DC Currents and Voltages) B2 -15V at -20mA 6V at + 20mA 7 Condition of RF Output J1-J2 Low Loss 7 Condition of RF Output J1-J3 Isolation Low Loss B3 6V at +20mA -15V at -20mA Isolation 7. As long as 20mA is applied through the on diodes, the voltage can vary. Application Circuit 8,9,10,11,12 Example: J1 to J2 Low Loss R1 = 250 R2 = 450 B2 = -15V B3 = 6V Notes: 8. Assume Vf ~ 1V at 20mA 9. R1 = 5V / 0.02A = 250; R2 = 9V / 0.02A = 450 10. PR1 = 0.02A x 0.02A x 250 = 0.1 W 11. PR2 = 0.02A x 0.02A x 450 = 0.18 W 12. Inductors are bias RF chokes. The operating band width of a broad-band PIN diode switch is often dependent on the bias components, particularly the RF bias chokes. It is suggested that the frequency response be checked with all the bias components attached before installing the PIN diode. 4 ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions * North America Tel: 800.366.2266 * Europe Tel: +353.21.244.6400 is considering for development. Performance is based on target specifications, simulated results, * India Tel: +91.80.43537383 * China Tel: +86.21.2407.1588 and/or prototype measurements. Commitment to develop is not guaranteed. Visit www.macomtech.com for additional data sheets and product information. PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology Solutions has under development. Performance is based on engineering tests. Specifications are typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available. M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make Commitment to produce in volume is not guaranteed. changes to the product(s) or information contained herein without notice. MASW-002103-1363 HMICTM Silicon PIN Diode SPDT Switch 50 MHz - 20 GHz MASW-002103-1363 Outline Drawing Top View 1545 Rev. V7 Side View 125 Back Metal J2 J3 2225 J1 Units are in m MASW- 002103-1363 DIM Width Length Thickness 5 Inches MIN 0.060 0.087 0.004 MAX 0.062 0.089 0.006 MIN 1.52 2.20 0.10 mm MAX 1.57 2.25 0.15 ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions * North America Tel: 800.366.2266 * Europe Tel: +353.21.244.6400 is considering for development. Performance is based on target specifications, simulated results, * India Tel: +91.80.43537383 * China Tel: +86.21.2407.1588 and/or prototype measurements. Commitment to develop is not guaranteed. Visit www.macomtech.com for additional data sheets and product information. PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology Solutions has under development. Performance is based on engineering tests. Specifications are typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available. M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make Commitment to produce in volume is not guaranteed. changes to the product(s) or information contained herein without notice. MASW-002103-1363 HMICTM Silicon PIN Diode SPDT Switch 50 MHz - 20 GHz Rev. V7 Handling Procedures Attachment to a circuit board is made simple through the use of standard surface mount technology. Mounting pads are conveniently located on the bottom surface of these devices and are removed from the active junction locations. These devices are well suited for solder attachment onto hard and soft substrates. The use of 80Au/20Sn, or RoHS compliant solders is recommended. For applications where the average power is 1W, conductive silver epoxy may also be used. Cure per manufacturers recommended time and temperature. Typically 1 hour at 150C. When soldering these devices to a hard substrate, a solder re-flow method is preferred. A vacuum tip pick-up tool and a force of 60 to100 grams applied to the top surface of the device while placing the chip is recommended. When soldering to soft substrates, such as Duroid, it is recommended to use a soft solder at the circuit board to mounting pad interface to minimize stress due to any TCE mismatches that may exist. Position the die so that its mounting pads are aligned with the circuit board mounting pads. Solder reflow should not be performed by causing heat to flow through the top surface of the die to the back. Since the HMIC glass is transparent, the edges of the mounting pads can be visually inspected through the die after attachment is completed. Typical re-flow profiles for Sn60/Pb40 and RoHS compliant solders is provided in Application Note M538 , "Surface Mounting Instructions" and can viewed on the MA-COM Technology Solutions website @ www.macomtech.com Sample Board Samples test boards are available upon request 6 ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions * North America Tel: 800.366.2266 * Europe Tel: +353.21.244.6400 is considering for development. Performance is based on target specifications, simulated results, * India Tel: +91.80.43537383 * China Tel: +86.21.2407.1588 and/or prototype measurements. Commitment to develop is not guaranteed. Visit www.macomtech.com for additional data sheets and product information. PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology Solutions has under development. Performance is based on engineering tests. Specifications are typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available. M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make Commitment to produce in volume is not guaranteed. changes to the product(s) or information contained herein without notice. MASW-002103-1363 HMICTM Silicon PIN Diode SPDT Switch 50 MHz - 20 GHz Pocket Tape Dimensions .157 .004 4.00 0.10 .079 .002 2.00 0.05 .157 .004 4.00 0.10 .059 .004 THRU 1.5 Rev. V7 .069 .004 1.75 0.10 +.012 +0.30 8.00 - 0.10 .093 .002 2.36 0.05 0.035 THRU TYP. 0.89 .138 3.5 0.05 .012 .001 0.30 0.03 5 MAX. .012 .002 0.30 0.05 POCKET DEPTH .066 .002 1.80 0.05 Chip Orientation in Pocket 7 ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions * North America Tel: 800.366.2266 * Europe Tel: +353.21.244.6400 is considering for development. Performance is based on target specifications, simulated results, * India Tel: +91.80.43537383 * China Tel: +86.21.2407.1588 and/or prototype measurements. Commitment to develop is not guaranteed. Visit www.macomtech.com for additional data sheets and product information. PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology Solutions has under development. Performance is based on engineering tests. Specifications are typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available. M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make Commitment to produce in volume is not guaranteed. changes to the product(s) or information contained herein without notice. MASW-002103-1363 HMICTM Silicon PIN Diode SPDT Switch 50 MHz - 20 GHz Reel Information Rev. V7 W1 & W2 measured at hub W2 W1 B C A D N DIM A B C D N W1 W2 INCHES MIN. MAX. 6.98 .059 .504 .795 2.14 .331 -- 7.02 .098 .520 .815 2.19 .337 .567 MM MIN. 177.3 1.5 12.8 20.2 54.5 8.4 -- MAX. 178.3 2.5 13.2 20.7 55.5 8.55 14.4 8 ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions * North America Tel: 800.366.2266 * Europe Tel: +353.21.244.6400 is considering for development. Performance is based on target specifications, simulated results, * India Tel: +91.80.43537383 * China Tel: +86.21.2407.1588 and/or prototype measurements. Commitment to develop is not guaranteed. Visit www.macomtech.com for additional data sheets and product information. PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology Solutions has under development. Performance is based on engineering tests. Specifications are typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available. M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make Commitment to produce in volume is not guaranteed. changes to the product(s) or information contained herein without notice. |
Price & Availability of MASW-002103-1363V7
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |